|
Centre axle Model BK
Individually designed mobile loading ramps direct from the manufacturer
Mobile loading ramps from BUTT combine efficiency, mobility and quality for your loading activities.
BUTT – mid-axle range for head-on loading is the classic solution for loading and unloading cargo from trucks and containers and supports your logistic tasks at just the right height. The easy-to-use BK models make an essential contribution to optimising your logistics process. Apart from the most commonly chosen variants, BUTT also develops and produces according to your requirements. We look forward to speaking to you!
- Optimum positioning of the ramp due to centrally located swimming axle reducing the need for manoeuvring
- Simple setting of working heights via manually operated hydraulic pump (also available with electro-hydraulic pump)
- Safety chains – quick lock for fixing the mobile loading ramp to the container/truck
- Swimming axle which compensates for the suspension of the truck/container
- Cardan joint fork clamp for quick positioning of the ramp before and after the loading operation. Also available as manoeuvring device for fork lift loaders with bale clamps (one-man operation)
- Open, anti-slip hot-dip galvanised safety frame in high strength design for safe driving under all conditions. Repels snow, slush and large dirt particles
- Lateral side bar protection as standard
- Low maintenance special heavy load wheels designed by us with cast rims and double ball bearings, lubricating nipple and press on full rubber tyres with steel wire reinforcement
The equipment of all BUTT mobile loading ramps can be adapted to your requirements. |
 |
 |
Total load carrying capacity 9,000 kg. for use with diesel and gas driven fork lift loaders or modern electro stackers
| Load carrying capacity: |
9.000 |
kg |
a |
11.800 |
mm |
| Total length: |
11.800 |
mm |
b |
2.500 |
mm |
| Total width: |
2.300 |
mm |
c |
(min.) 1.100 |
mm |
| Driving width: |
1.960 |
mm |
|
(max.) 1.750 |
mm |
| Lip width: |
2.140 |
mm |
|
|
|
| Lip length: |
400 |
mm |
|
|
|
|
 |
Specially developed for the loading of particularly high cargoes easily and safely over 3,500 long horizontal.
| Load carrying capacity: |
7.000 |
kg |
a |
12.800 |
mm |
| Total length: |
12.800 |
mm |
b |
3.500 |
mm |
| Total width: |
2.300 |
mm |
c |
(min.) 1.100 |
mm |
| Driving width: |
1.960 |
mm |
|
(max.) 1.750 |
mm |
| Lip width: |
2.140 |
mm |
|
|
|
| Lip length: |
400 |
mm |
|
|
|
|
 |
Specially suited for electro stackers in order to keep battery power loss as low as possible by means of a favourable ramp incline.*
*Type BK 912 can also be used electro stackers made after 1990) .
| Load carrying capacity: |
7.000 |
kg |
a |
14.800 |
mm |
| Total length: |
14.800 |
mm |
b |
3.500 |
mm |
| Total width: |
2.300 |
mm |
c |
(min.) 1.100 |
mm |
| Driving width: |
1.960 |
mm |
|
(max.) 1.750 |
mm |
| Lip width: |
2.140 |
mm |
|
|
|
| Lip length: |
400 |
mm |
|
|
|
|
|
 |
Front axle Model BKV for front side loading
Mobile loading ramps ideally matched to your logistic requirements
BUTT mobile loading ramps with front-axle for head-on loading in the BKV range.
The BUTT BKV range of ramps with front-axle for head-on loading combines all the advantages of the BK series and can be used in all those situations where above-average loading and unloading stresses arise. All the equipment of the BUTT mobile loading ramps in the BKV range can be adapted to your special requirements!
- Broad driving area enabling comfortable up and down driving
- Simple setting of the working height via mechanical winch (also available with electromechanical drive)
- Safety chains – quick lock for fixing the mobile loading ramp to the container/truck
- Cardan joint fork clamp for quick positioning of the ramp before and after the loading operation. Also available as manoeuvring device for fork lift loaders with bale clamps (one-man operation)
- Open, anti-slip hot-dip galvanised safety frame in high strength design for safe driving under all conditions. Repels snow, slush and large dirt particles
- Lateral side bar protection as standard
- Low maintenance special heavy load wheels designed by us with cast rims and double ball bearings, lubricating nipple and press on full rubber tyres with steel wire reinforcement
|
 |
 |
Total load carrying capacity 10,000 kg. For head-on loading
| Load carrying capacity: |
10.000 |
kg |
a |
11.800 |
mm |
| Total length: |
11.800 |
mm |
b |
2.500 |
mm |
| Total width: |
2.300 |
mm |
c |
(min.) 1.200 |
mm |
| Driving width: |
1.960 |
mm |
|
(max.) 1.650 |
mm |
| Lip width: |
2.000 |
mm |
|
|
|
| Lip length: |
600 |
mm |
|
|
|
|
|
|
Front axle Model BKV loading on three sides
Mobile loading ramps are flexible and efficient partners for your logistic needs
BUTT mobile loading ramp for 3-sided loading with height adjustable front axle in the BKV type range.
The 3-sided loading ramp with front axle is a highly flexible mobile loading ramp and represents the simplest way of optimising your loading and unloading operations.
- Centrally divided barrier lips set horizontally for lateral and head-on loading.
- Manual support winch, also available with electric height adjustment
|
Total load carrying capacity : 10,000 kg. for 3-side loading
| Load carrying capacity: |
10.000 |
kg |
a |
12.500 |
mm |
| Total length: |
12.500 |
mm |
b |
3.200 |
mm |
| Total width: |
3.000 |
mm |
c |
3.000 |
mm |
| Driving width: |
1.960 |
mm |
d |
(min.) 1.200 |
mm |
| Lip width: |
2.000 |
mm |
|
(max.) 1.650 |
mm |
| Lip length: |
600 (500) |
mm |
|
|
|
|
|
|
Picture gallery
Please click on the thumbnail to get a larger picture.
|
|
|
Click to play the
Flash-Video file. |
|
You will find some references of our mobile loading ramps in the following
picture gallery.
|
|
